GD&T and Tolerance Stack-Up PUBLIC WORKSHOPS
/EINPresswire.com/
GD&T and Tolerance Stack-Up Analysis - PUBLIC WORKSHOPS
December 5-9, 2011
Bevill Conference Center, Huntsville, AL.
Courses are 2 ½ days each—--take one or both.
GD&T [per the ASME Y14.5-2009 and 1994 standards and the differences between them] and TOLERANCE STACK-UP ANALYSIS. Both courses presented by GDT 'expert' James D. Meadows. Discounts available for govt. employees and contractors and multiple registrations.
1) Geometric Dimensioning and Tolerancing (per ASME Y14.5-2009 and 1994 and the differences between them)
December 5-7, 2011
An introductory, but comprehensive, applications-based training program for all technical personnel who interpret and apply geometric dimensioning and tolerancing. This course covers GDT principles, rules and applications, as well as the new Y14,5-2009 symbology. Participants will gain a comprehensive knowledge of GD&T techniques but also, through the use of lectures, discussion, case histories and application problems, the ability to apply these techniques to their product line.
2) Tolerance Stack-Up Analysis.
December 7-9, 2011
Participants will be trained to apply tolerance stack-up analysis techniques, from the very simple to more complex situations. Both plus and minus and geometrically toleranced assemblies will be examined and stack-up analysis taught and practiced on each. Some concepts taught: loop analysis, number charting, virtual condition, resultant condition, inner/outer boundaries, minimum airspace, maximum wall thickness, maximum interference, minimum and maximum overall dimensions, fixed and floating fastener assembly conditions, projected tolerance zones, the logic of stack-up analysis, statistical tolerancing, etc. Learn a system of logic and mathematics to analyze tolerances; Calculate statistical tolerance using a variety of methods and learn how to re-integrate these tolerances back into the assembly's details, etc.
James D. Meadows--ASME Sr. Level GDTP, author of 15 textbooks on GD&T and related topics (many best-selling), an active member of 12 ASME/ANSI/ISO committees that write the standards for US and international communities, a dynamic communicator, and has been a full-time GD&T trainer/consultant for 25+ years. Clients include private sector industries, universities, ASME and the government/government contractors.
Go to www.geotolmeadows.com under 'Public Workshops' for more course and registration details or call (615) 824-8644.
GD&T and Tolerance Stack-Up Analysis - PUBLIC WORKSHOPS
December 5-9, 2011
Bevill Conference Center, Huntsville, AL.
Courses are 2 ½ days each—--take one or both.
GD&T [per the ASME Y14.5-2009 and 1994 standards and the differences between them] and TOLERANCE STACK-UP ANALYSIS. Both courses presented by GDT 'expert' James D. Meadows. Discounts available for govt. employees and contractors and multiple registrations.
1) Geometric Dimensioning and Tolerancing (per ASME Y14.5-2009 and 1994 and the differences between them)
December 5-7, 2011
An introductory, but comprehensive, applications-based training program for all technical personnel who interpret and apply geometric dimensioning and tolerancing. This course covers GDT principles, rules and applications, as well as the new Y14,5-2009 symbology. Participants will gain a comprehensive knowledge of GD&T techniques but also, through the use of lectures, discussion, case histories and application problems, the ability to apply these techniques to their product line.
2) Tolerance Stack-Up Analysis.
December 7-9, 2011
Participants will be trained to apply tolerance stack-up analysis techniques, from the very simple to more complex situations. Both plus and minus and geometrically toleranced assemblies will be examined and stack-up analysis taught and practiced on each. Some concepts taught: loop analysis, number charting, virtual condition, resultant condition, inner/outer boundaries, minimum airspace, maximum wall thickness, maximum interference, minimum and maximum overall dimensions, fixed and floating fastener assembly conditions, projected tolerance zones, the logic of stack-up analysis, statistical tolerancing, etc. Learn a system of logic and mathematics to analyze tolerances; Calculate statistical tolerance using a variety of methods and learn how to re-integrate these tolerances back into the assembly's details, etc.
James D. Meadows--ASME Sr. Level GDTP, author of 15 textbooks on GD&T and related topics (many best-selling), an active member of 12 ASME/ANSI/ISO committees that write the standards for US and international communities, a dynamic communicator, and has been a full-time GD&T trainer/consultant for 25+ years. Clients include private sector industries, universities, ASME and the government/government contractors.
Go to www.geotolmeadows.com under 'Public Workshops' for more course and registration details or call (615) 824-8644.
Follow us
What people say
“We have generated many, many press clippings and improved our SEO ranking from the services that EIN Presswire provides us. Easy and simple way to upload and distribute our press releases. I would recommend their services.”
— Chris Morris, Marketing Manager of Mountz Inc.
“I have been using the EIN Press Release service for more than three years in entertainment & health care industries. Their account managers and the placement of my press releases online has been above reproach reaching mainstream journalists to help further client and brand visibility. I highly recommend this service for global notoriety and am thankful I made that first call.“
— Monica Anders PR Strategist 25 Years!
Our Partners
Press releases
- Fish & Richardson Principal Juanita R. Brooks Named "Top Female Trial Attorney" by Law360 [23 May 2012] PR Newswire
© 2005-2012